Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Flower Mound: What to Know First
Independent FAAC gate motor and opener service in Flower Mound is what we do at Ironworks Gate Co., and most FAAC jobs are diagnosed and repaired in a single visit. A typical FAAC repair runs between $220 and $480 depending on the part and the labor involved, and you’ll always know the price before we turn a single bolt. No surprises, no padding, no vague estimates.
If you have a FAAC gate that groans, stops mid-travel, or simply will not open, this page is for you. We work on the FAAC systems that show up in Flower Mound driveways, and we know their specific failure patterns by heart. Call (254) 345-4831 and a live person answers – day or night. Victor Salinas grew up in the Lakeside area, and we’ve been fixing gates in this town for over 42 years.
How FAAC Products Fail - and How We Fix Them
FAAC makes a solid operator. The hydraulic 400 and 770 series, the electromechanical 390 and 412, the C720 and S800 slide units – they’re all built heavier than most. But every brand has its habits, and FAAC has a few we see over and over in Flower Mound. Here are the real failure modes, stripped of guesswork:
- FAAC 400 and 770 series slow operation in cold weather. These hydraulic operators use thin oil that thickens when North Texas gets a hard freeze. The gate creeps open or stalls entirely. We flush the system and refill with the proper viscosity for our climate, then test the pressure relief. Fixing it now beats a dead motor in February.
- FAAC 412 and 390 control board failure after storms. Lightning and power surges in Flower Mound are rough on FAAC control boards. The symptom is easy to miss – the gate opens but won’t close, or the remote works only from ten feet away. We test the board, replace failed relays or the board itself, and add surge suppression so it doesn’t happen again next spring.
- FAAC C720 slide motor grinding on the rack. When the nylon gear wears or the rack shifts out of alignment, you’ll hear a grinding sound on every cycle. Run it too long and you’re replacing the gearbox, not just the gear. We catch this early, realign the rack, and replace the worn gear before the motor takes damage.
- FAAC S800 limit switch drift. Older FAAC slide operators lose their limit settings gradually. The gate over-travels, bangs the stop, and reverses. Simple recalibration usually fixes it. If the limit switch itself is worn, we replace it with an OEM part and set the slow-down points correctly.
- FAAC photocell and safety edge nuisance trips. Flower Mound gets dust, pollen, and heavy sun. FAAC safety sensors get dirty or sun-blinded, and the gate refuses to close or reverses halfway. We clean, realign, and shield the sensors. If a safety edge is cracked or waterlogged, we replace it – this is a safety-critical part, not a corner to cut.
Our FAAC Gate Motor & Opener Process
- 1
You call. A live person picks up at (254) 345-4831. We ask what the gate is doing – or not doing – and schedule a visit. If it’s an emergency, we move fast. If it can wait a day, we tell you that too.
- 2
We diagnose on-site. Our technician tests the operator, the board, the limits, and the safety circuit. On a FAAC, we check the specific weak points: oil condition, surge damage, gear wear, and sensor alignment.
- 3
You get a straight price. Before any work starts, you’ll know exactly what the repair costs. We discuss OEM versus quality aftermarket parts if that’s relevant – on some FAAC parts we insist on OEM, on others a proven aftermarket part saves you money without cutting corners.
- 4
We do the work. Most FAAC repairs happen in one visit. The part goes in, the settings get dialed in, and the whole system gets a full operational test.
- 5
We test it like we own it. We cycle the gate repeatedly, check the force settings, verify the safety edges and photocells, and make sure the remote range is right. A gate that closes on a car or a kid is not acceptable – period.
- 6
You get the 90-Day Done Right Promise. Written, straightforward. If it’s not right, we come back and make it right. No paperwork, no arguing. Every single job.
What FAAC Gate Motor & Opener Costs in Flower Mound
Here are honest ranges for the FAAC repairs we handle most often in Flower Mound. Every price is quoted and agreed before work begins – you’ll never get a surprise invoice from us.
- FAAC control board replacement: $280 to $520, depending on the series. A 390 board costs less than a 770 board. We stock common boards and can usually get uncommon ones within two or three days.
- FAAC hydraulic service (400/770): $180 to $320 for a full flush, refill, and pressure adjustment. Catch it before the pump burns out and this is all you’ll spend.
- FAAC gear or gearbox replacement (C720/S800): $190 to $410. The gear itself is affordable; the gearbox is more. We’ll tell you which one you actually need.
- FAAC sensor or safety edge repair: $130 to $260. Safety parts are not where you want to pinch pennies.
- FAAC limit switch service: $95 to $180 for recalibration, or switch replacement if it’s gone bad.
What moves the price is parts availability and access. A gate operator in a tight corner with no clearance takes longer. A rusted mount that needs welding adds shop time. We’ll give you the exact number before we start, and estimates are always free. Call (254) 345-4831 and we’ll give you a straight answer.
Why Flower Mound Homeowners Call Ironworks Gate Co. for FAAC Work
We’ve been fixing gates in Flower Mound since the town was mostly open land and gravel roads. Victor Salinas learned welding and electrical work at Tarrant County College, where an old instructor told him that metal remembers how it was treated. The same is true of customers. We’ve kept that in mind for over 42 years, and it’s why homeowners call us when their FAAC operator quits.
Our technicians are trained on nine automation brands – FAAC included – along with LiftMaster, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If you have a LiftMaster keypad on a FAAC operator, or a Mighty Mule gate with a Ghost Controls remote, we fix the whole system in one visit instead of telling you to call someone else. Background-checked, uniformed techs. A live person on the phone 24 hours a day. A written 90-Day Done Right Promise on every job. And a price you agree to before the work starts.
FAQs
We service FAAC equipment under warranty as an independent provider, but we don’t process manufacturer warranty claims. If your unit is under warranty, we’ll diagnose the problem and tell you exactly what failed. You can then decide whether to file a claim or have us fix it directly. Many Flower Mound homeowners choose the direct route because waiting on warranty processing can leave a gate inoperable for weeks.
We keep common FAAC parts on hand: control boards for the 390 and 412 series, hydraulic oil for the 400 and 770, gears for the C720 and S800, sensors, and safety edges. Oddball parts usually arrive in two to three days. We’ll tell you up front if a part needs to be ordered, so you’re never left guessing why the gate is still down.
If the motor itself is still sound and the frame is solid, repair almost always makes more sense than replacement. FAAC operators are built to last, and a $300 control board beats a $2,000 replacement. But if the motor is burned out, the gearbox is shot, and the unit is fifteen years old, we’ll tell you that too – and we won’t upsell you into a new system you don’t need. Call (254) 345-4831 and we’ll give you the honest answer.
Yes. We regularly integrate battery backup systems, keypads, intercoms, and vehicle sensors with existing FAAC operators. The FAAC control architecture is straightforward to work with, and we wire everything cleanly and test it before we leave. If Flower Mound loses power, you still get in and out.
In most cases we can have a technician on-site the same day you call, and a live person answers the phone 24 hours a day at (254) 345-4831. A gate stuck open is a security problem. A gate stuck closed is a safety problem. Either way, we’ll be there when we say.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Flower Mound and nearby areas.