Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Flower Mound: What to Know First
Linear gate installation in Flower Mound follows a straightforward path when the right people do the work. We’re an independent Linear service provider, not a factory arm, and we install, wire, weld, and automate Linear gates so they close square and run quiet from the first day. Most single-gate installations take one full day on site, and you get a written price before we start. If you own Linear equipment and want it installed without surprises, call (254) 345-4831.
This page is for homeowners in Flower Mound who already own Linear gate hardware, or who are planning a Linear-equipped gate, and want to know what a proper installation looks like. It covers the failure points we see most, what a real install costs in this area, and why Linear gear responds well to a company that repairs all nine major opener brands. No brand fluff here. Just what forty-plus years in gate work teaches you.
How Linear Products Fail - and How We Fix Them
- Linear LA400 and LA500 swing-arm operators losing limit memory. These two are the most common Linear operators on Flower Mound driveways. The control board’s memory chip loses its limit settings after a power brownout or a lightning flicker, which is common in Texas storm season. The gate then opens halfway, reverses early, or sits against the post grinding. We reflash limits and, where needed, install a small surge protector so the next storm doesn’t eat the board again.
- Linear LRA series slide operators with dead run capacitors. Run capacitors on the LRA slide units wear out in Flower Mound’s heat. A homeowner hears a buzz but the gate doesn’t move. It’s a $60 part and thirty minutes of work, not a new operator. We replace with the correct capacitance rating, never an overspec unit that burns the motor winding.
- Linear APeX and MegaCode receivers dropping remote programming. When a homeowner holds the remote and nothing happens, the receiver has usually lost its code table after years of power cycles. We reprogram and verify the antenna path, then confirm the receiver is properly grounded. Many Flower Mound installs from the early 2000s have receivers mounted inside metal enclosures with the antenna coiled, which cuts range badly.
- OEM vs. aftermarket control boards. Linear boards are not cheap. We will use OEM Linear boards whenever the gate is under warranty or when the job calls for it. On out-of-warranty builders-grade operators, a quality aftermarket board with matching voltage and protection circuits does the job for significantly less. We tell you which we recommend and why, before we order anything.
- Weld-on bracket failures on Linear piston arms. Linear piston operators ship with bolt-on posts and brackets. On Flower Mound black clay soil, gates settle and posts shift, which puts side-load on the piston arm until the bracket tears off or the pin wallows out. We weld reinforcement gussets and check post plumb before mounting any operator. The motor might be fine. The metal carrying it often isn’t.
Our Linear Gate Installation Process
- 1
Call and talk to a person. You reach a live body at (254) 345-4831, any hour. We ask what the gate is doing, what operator it has, and whether there’s a photo in your phone you can describe. We schedule a visit that fits your week.
- 2
On-site diagnosis. A background-checked technician shows up in our truck, walks the gate, opens the operator cover, and tests the board, motor, limits, and the gate’s physical movement. We measure post plumb, hinge wear, and gate level before touching the operator. On a Linear job, the problem is usually not where the homeowner thinks.
- 3
Straightforward pricing. We quote the job in writing: parts, labor, any weld work, and disposal of old components. You approve the number. The price never changes after you approve it.
- 4
The installation. We install the operator, brackets, arms, wiring, safety edges, and any photo eyes to Linear’s wiring diagrams. Every fitting is torqued, every wire landed on the right terminal, and every limit set for the actual gate travel, not a rough guess.
- 5
Testing and cleanup. We run the gate through full open-close cycles, test obstruction reversal, remote range, and keypad codes. We sweep the work area and walk you through what we did. The 90-Day Done Right Promise covers the work in writing.
What Linear Gate Installation Costs in Flower Mound
Here’s what our customers in Flower Mound typically pay for a complete Linear operator installation, including labor, brackets, and wiring:
- Single swing gate, Linear LA400 or LA500: $850 to $1,400 installed
- Single slide gate, Linear LRA series: $1,200 to $2,000 installed
- Double swing gate, dual Linear piston operators: $1,900 to $2,800 installed
- Pedestrian gate with Linear swing operator: $700 to $1,100 installed
- Replacement control board only: $180 to $350 parts and labor
What moves the price: gate size and weight, whether posts need weld reinforcement, whether we need to run new electrical conduit, and whether you want keypads tied into your operator. We do not charge to walk the job. Estimate is free, and the quote is what you pay. Call (254) 345-4831 to get a real number.
Why Flower Mound Homeowners Call Ironworks Gate Co. for Linear Work
We’re a gate company. Not a handyman with a truck, not a general contractor who occasionally hangs a gate. Linear operators are one brand among nine we service daily: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That cross-brand experience helps us spot a bad Linear install from forty feet away, because we know what the other brands would do in the same position. We’re led by Victor Salinas, who grew up in the Lakeside area back when it was open land and gravel roads. The company has served Flower Mound and nearby communities for over 42 years. Every job ends with the same thing: a written 90-Day Done Right Promise. If it is not right, we come back. No arguing, no paperwork dance, no exceptions. That’s the Keystone Standard.
FAQs
On operators still under Linear’s factory warranty, we follow manufacturer installation specs precisely so your warranty stays intact. We are an independent provider, not a Linear factory shop. Any repair we touch is covered by our own 90-Day Done Right Promise regardless of the factory status. Call (254) 345-4831 and we’ll tell you exactly where you stand.
In most cases we can get a Linear operator installed in Flower Mound within three to five business days of the estimate, faster if the parts are in our truck or local stock. We do not promise same-day on new installations because measuring, ordering, and doing it right takes the time it takes. We will give you a straight date when we quote the job.
If the board is sound and the motor hasn’t been overheated, repairing an older Linear operator often makes sense, especially a well-maintained unit. If you have had multiple failures in one year or the motor windings are scorched, we’ll tell you plainly and price a replacement against another repair that may not hold. We don’t sell toward the bigger bill. We tell you the truth.
Yes. We run the power, land the wiring, install photo eyes and safety edges, and set the obstruction-reversal force to the gate’s actual weight and travel. Linear installs in Flower Mound often fail because whoever installed the gate skipped the safety loop wires or left the ground floating. We wire it like it matters, because it does.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Flower Mound and nearby areas.