Linear Access Control Installation Nationwide

Linear Access Control Installation: The Flower Mound Owner’s Guide

We stock and install Linear access control components across Flower Mound, with most full swaps running $425 to $1,150 installed depending on which Linear board or receiver your system uses. A failed access control board is usually discovered the same way every time: the remote stops working, the keypad goes dark, or the gate simply ignores every command sent its way. Victor Salinas has replaced enough Linear control boards in Flower Mound to know exactly what fails first and what can be saved.

Call (254) 345-4831

Most Flower Mound homeowners don’t think about their gate’s access control until it quits. One morning the remote works. The next morning, nothing. The gate sits there like a mule that’s made up its mind. That’s the access control board telling you it’s done, and no amount of fresh remote batteries will change that.

Which Linear Models This Applies To

Linear built its reputation on the APeX and MegaCode receiver families, and those remain the most common units we replace across Flower Mound. The APeX series covers the older AP-3, AP-4, and AP-5 receivers, while MegaCode runs the MCS and MCT lines. If your gate opener has a Linear label but you’re unsure which board it uses, open the cover and look for a small white sticker with a model number printed in black. That number is the difference between ordering the right part the first time and guessing.

Here’s the compatibility gotcha most owners don’t know: MegaCode receivers listen on 318 MHz, while some older APeX units run 303 MHz. A receiver keyed to the wrong frequency will test fine on the bench and still never open a gate. Ironworks Gate Co. is an independent service provider, not affiliated with Linear, but our techs carry the frequency meters to verify a board before it goes in. For OEM versus aftermarket, we stock genuine Linear boards for current production models and quality aftermarket equivalents for discontinued APeX units where Linear no longer supplies the part.

Signs Your Linear Access Control Installation Is Failing

• Remote range shrinks to near zero. You used to open the gate from the end of the street. Now you’re holding the remote against the windshield and still getting nothing. That’s the receiver section of the board losing sensitivity, and it only gets worse.
• Keypad lights up but the gate ignores it. The keypad beeps, the display flashes, everything looks right, and the gate does not move. That’s the relay output on the control board failing closed. The keypad is talking; the board isn’t listening.
• Gate opens randomly with no one at the keypad. A fluttering relay or a failing wireless receiver can trigger phantom openings. In Flower Mound, where afternoon storms roll through with real lightning, we see surge damage cause exactly this.
• You hear a click but nothing happens. The board’s relay is energizing, but the contacts are too pitted to carry current to the motor. The click is the relay throwing. The silence after it is the board failing a hundred times a day.
• Intermittent operation that comes and goes with the weather. Texas heat and humidity work on solder joints and capacitors. A board that fails on a hot afternoon and works fine at dawn has a thermal crack somewhere on the board.

Replacement Cost & What’s Included

Installed Linear access control replacement in Flower Mound runs $425 to $1,150 for most residential systems. The spread comes down to which Linear board your gate uses, whether we’re replacing just the receiver or the full control assembly, and how much wiring has to be redone from the board to the motor. A straight receiver swap lands at the low end. A full board-and-harness replacement with weatherproofing lands at the top.

Every quote is settled before work begins. You’ll know the part cost, the labor cost, and the total, in writing, before a single screw comes out. No surprises on the bill. Every installation carries our written 90-Day Done Right Promise: if it’s not right, we come back and make it right. No arguing, no paperwork, no exceptions. And remember our standing offer: $50 Off Any Repair Over $250, plus a permanent 5% Senior and Veteran discount.

DIY or Call Us?

Line-voltage and low-voltage both live inside a gate operator, and while 12 or 24 volt control wiring won’t generally hurt you, a wrong connection between the board and the motor can fry your opener entirely. What Victor learned from an old instructor at Tarrant County College still holds: metal remembers how it was treated. So do control boards that get wired backward.

We never try to keep a homeowner from understanding their own gate. You can safely check power to the operator, look for a tripped GFCI, and verify the remote’s battery. But when the board itself is failing, the safest move is to call someone who has replaced hundreds of them. Call (254) 345-4831 and we’ll have a technician out to Flower Mound, diagnose the board, and quote a fix on the spot.

FAQs