Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Gate Installation in Flower Mound: What to Know First
Elite gate installation in Flower Mound typically runs $2,800 to $7,500 for a complete driveway gate with automation, and most jobs are finished within one to two weeks of the site visit. As an independent Elite service provider, we install, wire, and program Elite openers and gates without the inflated pricing you sometimes see from factory-authorized shops. We quote every job upfront, in writing, before any work begins.
This page is for Flower Mound homeowners who already own an Elite system or are considering one, and who want an installer that actually knows the equipment. If you have questions about your specific property, call (254) 345-4831. A live person answers, day or night.
How Elite Products Fail - and How We Fix Them
Elite builds solid gates, but after enough Texas summers and clay-soil shifting, every brand shows its age. Here is what we see most often on Elite jobs around Flower Mound:
- Elite SL-3000 slide gate arms snapping at the drive chain. The SL-3000 series uses a chain-drive carriage that takes a beating when the track sits on shifting clay. Flower Mound soil expands and contracts hard with the wet-dry cycle, and the track drifts out of level by a quarter inch or more. The motor keeps pulling, the chain binds, and the arm fractures. We re-level the track, replace the arm with a reinforced aftermarket part, and re-tension the chain. Most shops just swap the arm and call it done, and six months later it snaps again.
- Elite RG2200 gearbox wear causing gate creep. The RG2200 is a workhorse opener, but after eight to ten years the brass drive gear inside the gearbox rounds off. The gate starts creeping open or closed on its own after it cycles. Elite sells the gearbox as an assembly; we source the individual gear through a supplier in Garland and rebuild the box for about half the cost. You get the same result without paying OEM markup on a whole assembly.
- Elite photo-eye misalignment from concrete heave. Every Elite opener ships with photo-eye sensors that mount on the gate posts. When the driveway slab shifts, the posts lean, and the sensors drift out of line. The gate refuses to close, or reverses mid-cycle. We see this constantly in Flower Mound subdivisions built before 2000, where slab footings were poured thinner. The fix is re-shimming the sensor mounts and re-aligning the beam, not replacing the eyes. A cheap part costs you a service call either way; doing it right the first time saves the second call.
- Elite SL-1500 control board failure from power surges. North Texas thunderstorms send surges through overhead lines, and the SL-1500 board has a capacitor bank that takes the hit. When the board goes, the gate loses its limits and the opener runs blind. We install a surge suppressor at the breaker as part of every Elite installation now. It is a $60 part that saves a $400 board. Elite’s own documentation does not mention this, but forty years of Texas weather taught us.
- Elite pedestrian gate hinge wear on uneven ground. The lighter Elite pedestrian gates used on side yards and pool entries tend to sag when the post settles. The hinge barrels oval out and the gate drags the latch side. We replace the hinges with sealed-bearing units and reset the post in concrete that goes below the frost line. It is a one-day job, and the gate swings clean for another decade.
Our Elite Gate Installation Process
Every Elite job follows the same sequence, whether it is a fresh install or a replacement on an existing fence line. Nothing gets skipped, and nothing gets added to the bill without a conversation first.
- 1
Site walk and measurements. We check gate width, post condition, ground slope, power availability, and how the gate will swing or slide. If it is a replacement, we document the existing Elite model and what failed.
- 2
Written quote with two numbers. You get the OEM parts price and the quality aftermarket option side by side, plus the labor. We settle the price before any work starts.
- 3
Post setting and gate mounting. We set posts in concrete, hang the gate, and verify it swings or slides square to the post. A gate that fights its hinges wears out openers fast.
- 4
Elite opener installation and programming. We wire the motor, set the limits, and program the remotes. If you have a keypad or access control, we tie it in during this step.
- 5
Testing and weather-sealing. We cycle the gate fifteen to twenty times, check the safety edges, and seal every connection against moisture. North Texas heat and humidity are hard on exposed wiring.
- 6
Walkthrough and the 90-Day Done Right Promise. We show you how everything works, hand you the written guarantee, and leave the site cleaner than we found it.
What Elite Gate Installation Costs in Flower Mound
Honest numbers for the Flower Mound market, based on what we have quoted across Denton County this year:
- Pedestrian gate with Elite opener: $2,800 to $4,200 installed
- Single swing driveway gate, Elite SL-1500: $3,500 to $5,500 installed
- Double swing driveway gate, Elite RG2200: $5,000 to $7,500 installed
- Sliding driveway gate, Elite SL-3000: $4,500 to $7,000 installed
- Replacing an existing Elite opener only: $900 to $1,800 including labor and programming
What moves the price: gate size, whether you need new posts or the existing ones are solid, how far the power needs to run, and whether you want OEM Elite parts or equivalent aftermarket. We always give you the choice. Estimates are free. Call (254) 345-4831 and we will come measure.
Why Flower Mound Homeowners Call Ironworks Gate Co. for Elite Work
We have been doing gate work in Flower Mound for over 42 years. Victor Salinas grew up in the Lakeside area when most of this town was open land, and the company he runs now still treats every job like the neighbor is watching, because the neighbor usually is. We are trained and equipped on nine gate-automation brands, including Elite, so when we open the panel we know what we are looking at. And if your Elite system eventually needs an opener from LiftMaster, Mighty Mule, Ghost Controls, or DoorKing, we are already certified on those too.
Every job is backed by the 90-Day Done Right Promise in writing. No paperwork, no arguing. If it is not right, we come back and make it right. That is the Keystone Standard, and it applies to every single gate we hang.
FAQs
No. Choosing an independent installer does not void your Elite gate warranty, provided the installation is done to code and the opener is compatible with your gate. We only note here that Ironworks Gate Co. is an independent Elite service provider, not a factory-authorized dealer, and we do not imply otherwise.
We stock both, and we show you the price difference on every quote. OEM Elite parts carry the factory warranty; quality aftermarket parts often match or exceed OEM performance at a lower cost. We recommend based on what is on your gate and how long you plan to stay in the home. Call (254) 345-4831 for a straight answer on your setup.
Yes. Flower Mound properties have enough grade to make a direct slab pour marginal in some yards. We level the posts, build up the low side, and set the gate to swing or slide true. It takes longer, but a gate that fights the ground will eat openers.
Most installations begin within one to two weeks of the site visit. Repairs on existing Elite openers can often be same-day or next-day. The office is staffed 24/7, so call (254) 345-4831 any time and we will get you on the schedule.
If the gate itself is in good shape and the opener is under ten years old, repair is almost always the better money. We rebuild Elite gearboxes and replace boards for a fraction of a new opener. If the opener is fifteen years old and the gate is rusting through, we will tell you that too. We would rather be honest than be back in a year.
Contact Ironworks Gate Co.
If you are in Flower Mound and your Elite gate needs installation, repair, or a straight answer on price, call (254) 345-4831. A live person picks up. We will schedule a site visit, give you a written quote before any work starts, and stand behind the finished job in writing. Metal remembers how it was treated. So do customers.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Flower Mound and nearby areas.