Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Keypad & Intercom Repair: The Flower Mound Owner’s Guide
Elite keypad and intercom repair in Flower Mound typically runs $195-$425 installed, and most jobs are completed in a single visit because we stock the common Elite-compatible keypads, intercom modules, and wiring connectors on our trucks. The part itself is rarely the whole story: what fails first in North Texas is usually the weather seal around the keypad face, followed by the intercom speaker cone, which heat and humidity quietly destroy over three to five years.
Most Flower Mound homeowners discover the failure the same way: the gate opens fine from the car remote, but the keypad goes dead after a rainstorm, or the intercom voice turns to static and then silence. One component fails while the operator keeps working, and that mismatch is the giveaway that the problem is in the access hardware, not the motor.
Which Elite Models This Applies To
This page covers keypad and intercom repair for Elite swing and slide gate operators, including the SL-3000, SL-5000, and Mirage series, along with the earlier Elite DS and R series units still running in older Flower Mound neighborhoods like Wellington and Bridlewood. If you have an Elite operator with a separate keypad or an integrated intercom station, the guidance here applies. Ironworks Gate Co. is an independent service provider and not affiliated with Elite, but we work on their equipment every week.
The compatibility gotcha with Elite is voltage: older Elite DS-series keypads run on 12V DC, while the SL-3000 and newer units switched to 24V DC. A keypad that worked on your old operator will not survive on a new one, and we have seen homeowners buy the wrong part online and burn it out on installation. If the label on your keypad is faded, we identify the part by the wire count and the connector style, not by guesswork. For Elite specifically, we recommend OEM keypads when the gate gets daily use, but there are quality aftermarket equivalents that hold up fine for weekend-use driveway gates.
Signs Your Elite Keypad & Intercom Repair Is Failing
- Keypad goes dead after rain. The membrane seal has failed and water has reached the circuit board. In Flower Mound’s spring storm season, this is the most common failure we see. Once corrosion starts on the board traces, the keypad is done.
- Buttons work intermittently or require hard presses. The carbon contacts under the membrane are worn. This happens faster on gates that face west and sit in the afternoon sun. You can limp along for a few months, but the part is failing.
- Intercom buzzes or hums constantly. That is a failing speaker cone or a loose ground connection. The buzz means the circuit is live but the speaker cannot reproduce clean audio. We trace this in about twenty minutes.
- You can hear visitors, but they cannot hear you. The microphone element is shot, or the talk wire has corroded at the terminal block. Texas humidity gets into the housing through the speaker grille.
- Keypad works, but the gate does not respond. The keypad is fine; the relay it triggers is the problem. We test the keypad output first, so we do not sell you a part you do not need.
Replacement Cost & What’s Included
For Elite keypad and intercom repair in Flower Mound, plan on $195 to $425 installed. A basic single keypad swap on an existing mount runs $195 to $275. An intercom module replacement with new speaker and microphone runs $250 to $375. A full keypad-and-intercom replacement, when both have failed or the wiring is compromised, runs $350 to $425. The price includes the part, the labor, the weather sealing, and cleanup, and it is quoted and agreed before any work starts.
The range depends on three things: whether we are reusing the existing mounting pedestal or replacing it, how much of the low-voltage wire needs to be pulled, and whether we are matching OEM Elite hardware or a quality aftermarket equivalent. Every replacement carries our 90-Day Done Right Promise in writing, so if the keypad fails inside ninety days, we come back and make it right.
DIY or Call Us?
An honest split: you can safely check the obvious things yourself. Power cycle the operator at the breaker. Look at the keypad face for cracks in the membrane or condensation behind the lens. Tighten any loose screws at the terminal block if you are comfortable with a screwdriver. Low-voltage keypad work is not the same danger as a high-tension spring, but it can still bite: miswiring a 24V keypad into a 12V circuit will fry the board, and working on a gate control board without killing the power can damage the operator controller. That fix costs more than the keypad.
If the keypad still misbehaves after a power cycle, call us at (254) 345-4831. We will diagnose it on site, quote a fixed price, and usually finish the job the same day.
FAQs
Three to five years outdoors in North Texas is a realistic lifespan. Direct afternoon sun and spring rain cycles age the membrane seal faster than the electronics themselves. A keypad under a covered porch can last eight years or more.
Occasionally yes, and we will tell you when it is worth it. A bad solder joint or corroded terminal can be cleaned and reflowed. But once water has reached the circuit board or the membrane contacts are worn through, replacement is cheaper than repair and far more reliable. Call (254) 345-4831 for an honest diagnosis.
Most single-part replacements take forty-five to ninety minutes on site. A full keypad-and-intercom replacement with new wire runs about two hours. We quote the time and price before starting.
We stock the most common Elite-compatible keypads, intercom modules, and connectors on our trucks, along with parts for LiftMaster, Mighty Mule, and Ghost Controls. If your unit needs an uncommon part, we order it and return to install it, usually within two to three business days.
If your Elite keypad or intercom is giving you trouble, call Ironworks Gate Co. at (254) 345-4831. A live person answers, we will give you a straight answer about what is wrong and what it costs to fix, and the price will be settled before any work begins. Metal remembers how it was treated. So do customers.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Flower Mound and nearby areas.