Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Flower Mound: What to Know First
We install, replace, and retrofit FAAC gate operators and full gate systems throughout Flower Mound, and most FAAC installations are completed within two to five business days once we’ve ordered your operator and sized the job. As an independent FAAC service provider, we quote the full job before any work begins, so the price you approve is the price you pay. If you’re a Flower Mound homeowner with a FAAC operator that needs a new gate, a gate that needs a FAAC operator, or a full system going in from scratch, call (254) 345-4831 and we’ll come take measurements and give you a written number.
How FAAC Products Fail - and How We Fix Them
FAAC builds dependable equipment, but after forty-plus years of gate work we’ve learned exactly where each line tends to show its age. Here’s what we see on FAAC jobs in Flower Mound and how we address it during installation:
- FAAC 400 and 402 swing operators: worn capacitor and stuck limit cams. The 400 series is common on older Flower Mound estate gates, and the most frequent call we get is a gate that hums but won’t move. It’s usually the start capacitor giving out in the Texas heat, or the mechanical limit cams seizing after years of exposure. During installation we set the limits fresh and wire in a new capacitor, because the one that’s been in there since 2004 is not going to survive another Flower Mound summer.
- FAAC 750 and 760 sliding operators: stripped plastic drive gears. These are solid operators, but FAAC used a nylon gear in the drive train on many units. After ten or fifteen years, especially on heavier gates, those teeth shear. A new operator costs far more than the gear, but if the gate itself is misaligned or dragging, the new gear will strip too. We square the gate, correct the track, then install the operator so it runs clean.
- FAAC S418 and S450 hydraulic operators: fluid leaks at the fittings. Hydraulic FAAC units are smooth and quiet, but Flower Mound’s heat cycles cause the O-rings at the hydraulic fittings to harden and weep. A leaking operator is not just a mess on the driveway; it’s losing pressure every cycle. We reseal the fittings and top off the fluid during installation, then run a full pressure test.
- FAAC E024U control boards: fried relay from power surges. This is the one we see most after spring storms. North Texas lightning and grid surges come through Flower Mound and the relay on the E024U takes the hit. When we install a FAAC gate, we always recommend a surge protector on the incoming power line. It costs a few dollars and saves the board.
- FAAC XIB and XIBA keypad systems: dead zones on the membrane keypad. The keypads on older FAAC systems are exposed to full Texas sun, and the membrane eventually cracks from UV exposure. Buttons stop responding, or the whole pad goes dead. We stock replacement keypads and can retrofit a newer keypad to an older board, rather than selling you a whole new access system.
Our FAAC Gate Installation Process
Every FAAC installation we do in Flower Mound follows the same path from first call to final test. It’s not complicated, but it is deliberate, because a gate that’s installed wrong is a gate you’ll be calling about next month.
- 1
The call and the conversation. A live person answers at (254) 345-4831, day or night. We ask what FAAC model you have, whether the gate is swing or slide, and what it’s doing or not doing. Then we schedule a visit at a time that works for you.
- 2
The on-site assessment. We come out, inspect the existing gate, posts, hinges, and operator, and take measurements. We check what’s salvageable and what’s not. We do not sell you a full system if your brackets and gate are still solid.
- 3
The written quote. Before a single bolt is turned, you get a written price for the whole job. Labor, parts, operator, any welding or post work. If we find something else once we’re in the job that we should have caught, that’s on us, not on your bill.
- 4
The install. We either install the new FAAC operator on your existing gate, or install a new gate and operator together. For new gates, we build and weld in-house, so the gate and operator are matched from the start. We set limits, wire in safety edges and photo eyes where your layout calls for them, and surge-protect the power.
- 5
The test and the walkthrough. We run the gate through thirty full cycles, check the force settings, and show you how the manual release works. Then we show you the written 90-Day Done Right Promise and explain what it covers. No fine print. If something is not right, we come back and make it right.
- 6
The cleanup. We take our scraps, sweep the work area, and leave your property the way we found it. We do not leave you a box of leftover hardware and a receipt to figure out.
What FAAC Gate Installation Costs in Flower Mound
FAAC installation pricing in Flower Mound depends on whether you’re putting a new operator on an existing gate or building a new gate and automation package from scratch. Here are the numbers we typically quote:
- FAAC swing or slide operator installed on an existing, good-condition gate: $1,800 to $3,200
- New single swing gate with FAAC operator, installed: $4,500 to $7,500
- New double swing gate with FAAC operator, both leaves automated: $8,000 to $14,000
- New sliding gate with FAAC 750 or 844 operator, installed: $5,000 to $9,500
- Pedestrian gate with FAAC operator and keypad: $2,200 to $4,000
What moves the price is the gate’s weight and length, the condition of the posts and hinges, whether we’re running new power from the house, and whether you want keypads, remotes, or vehicle detection loops tied in. The quote we give you is the price you pay. Call (254) 345-4831 and we’ll come measure and give you an exact number. Estimates are free.
Why Flower Mound Homeowners Call Ironworks Gate Co. for FAAC Work
We’ve been fixing and installing gates in Flower Mound since 1984, and a good number of those jobs have FAAC operators on them. Our techs know the FAAC wiring diagrams without looking them up, and we stock the common parts, so we’re not waiting on a distributor while your gate sits open. But here’s the practical reason homeowners call us: if we find that your FAAC operator is beyond saving and the smart fix is a different brand, we work on eight other systems too. LiftMaster, Mighty Mule, Ghost Controls, DoorKing. We’re not married to one manufacturer; we’re married to the gate working right. Every job we do, FAAC included, is covered by our written 90-Day Done Right Promise, and a live person answers the phone when you call. That’s the deal.
Victor Salinas grew up in the Lakeside area of Flower Mound, back when most of this town was open land and gravel roads. He learned welding and electrical work at Tarrant County College, where an old instructor told him that metal remembers how it was treated. That line has carried through every FAAC gate we’ve installed since. Metal remembers how it was treated. So do customers.
FAQs
No, not if the installation is done correctly. As an independent FAAC service provider, we follow the manufacturer’s wiring and torque specifications on every install. The warranty on the operator itself stays intact when a qualified technician does the work. If we ever run into a parts claim, we’ll help you with it.
In most cases, yes. We install FAAC operators on existing gates all over Flower Mound, provided the gate itself is square, the posts are solid, and the hinges aren’t worn to the point of sag. If the gate needs welding or post work first, we’ll tell you before we start, and that work is included in the written quote.
If your FAAC operator is less than twelve years old and the failure is a capacitor, a gear, or a board relay, repairing it usually makes sense. If the operator is older, the housing is cracked, or the hydraulic unit is leaking from multiple points, replacement is often the more honest money. We’ll tell you which one we’d do on our own gate and give you the numbers for both. Call (254) 345-4831 and we’ll walk through it.
A straightforward operator swap on an existing gate is usually a single-day job. A full new gate and operator installation typically takes one to two days, depending on the size of the gate and the power run. We’ll give you a clear timeline on the written quote before we start.
Yes. We run the power from your panel or nearest junction box, and we install the safety edges and photo eyes that your gate layout requires. On a FAAC install we always recommend surge protection on the incoming power, because Flower Mound storms are hard on control boards. Every safety device is tested before we leave.
If you’ve got a FAAC gate that needs installing, replacing, or a second opinion on, call (254) 345-4831. We’ll come out, give you a straight answer, and a written price. No pressure, no surprises.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Flower Mound since 1984.