Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Flower Mound Homeowners
Gate Parts & Welding - Flower Mound typically means one of two things: a hinge or post has failed after years of North Texas weather, or a weld has cracked and the gate now sags against the latch. Most repairs run between $180 and $600 depending on what failed, and we complete the large majority of these jobs in a single visit. Ironworks Gate Co. has served Flower Mound homeowners since 1984, and owner Victor Salinas still runs every job to the same standard he set on day one: it gets done right, and it gets backed in writing.
If your gate is dragging, sagging, or making noise it never used to make, call (254) 345-4831. A live person answers, 24 hours a day, and we’ll tell you honestly whether it’s a simple part swap or a weld that needs a torch.
What Our Gate Parts & Welding Service Includes
Gate work splits into two categories: parts that wear out and metal that breaks. Both are our trade. We stock common hardware for Flower Mound’s most popular gate styles and we weld on site, so most calls are finished the same day we arrive. Here is what that covers, piece by piece.
Hinge Replacement
Hinges carry the entire weight of the gate every time it opens, and when one wears or bends, the gate drops and starts dragging against the ground. In Flower Mound’s clay soil, a gate that drags digs a groove fast, and that extra friction is exactly what finishes off a struggling opener motor. We replace worn or bent hinges with the correct weight-rated hardware for your gate, then weld or bolt them so the gate hangs square and swings clean.
If you see rust dust at the hinge or the gate has started scraping, that’s the hinge telling you it’s done. The fix is usually quick and far cheaper than waiting for the weld to tear or the post to crack.
Post Replacement
A gate post is set in concrete, and when a post leans or twists, it is almost never the welding that failed. It’s the footing, the post material, or years of soil movement under the slab. Ironworks Gate Co. removes the old post, checks the footing for cracks, and sets a new post square and true before re-hanging the gate to swing without binding.
Flower Mound soil shrinks and swells through every wet-dry cycle, and older posts sometimes simply rot at grade or snap at the weld point - that’s when you need Emergency Gate Parts & Welding in Flower Mound, TX. When we set a replacement, we set it to stay straight for decades, not seasons.
Rail Repair
Gate rails are the horizontal members that hold the pickets and give the gate its shape. When a rail rots, rusts through, or the pickets start rattling loose, the gate loses rigidity and begins to sway. We repair or replace rails, re-square the frame, and re-secure pickets so the gate does not wobble every time the wind picks up.
On ornamental steel gates, a cracked rail is often a five-minute weld that prevents a much larger failure. We would rather catch it early and charge you for five minutes than replace a twisted frame later.
Custom Welding
Not every gate fix comes off a shelf. When a scroll breaks, a frame cracks at a stress point, or a previous weld fails, the correct repair is a fresh weld done by someone who understands load and heat. Our technicians weld on site, grind the repair clean, and prime it so the fix does not rust out in two seasons.
We also build custom brackets, extend gates, and reinforce frames when a homeowner wants to add a motor to a gate that was never built for one. If it can be fixed with steel and a torch, we fix it.
Gate Rollers
Sliding gates ride on rollers, and when a roller seizes or flattens, the gate grinds along the track and the motor works double. We replace worn rollers, clean and align the track, and adjust the gate so it rolls with one hand again. On Flower Mound properties with long, heavy slide gates, roller wear is the single most common cause of motor burnout.
You will hear it before you see it: a grinding or chattering sound as the gate moves. That sound is a worn roller carving up the track, and ignoring it turns a $90 part into a full track replacement.
Latch & Lock
A latch that does not catch, a lock that sticks, or a gate that pops open when the wind gusts is a security problem and a safety problem. We adjust, repair, or replace latches and locks on both manual and automated gates, including mag-locks and solenoid locks tied into access control systems.
On automated gates, the latch works in sequence with the opener. If the latch is fighting the motor, the motor loses. We make sure both sides of that equation work together.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We work on gates paired with Mighty Mule and LiftMaster openers more than any other brands in Flower Mound, and we keep common hardware for both on the truck. A Mighty Mule gate that has sagged and torn a hinge is something we see weekly. The repair is usually straightforward: replace the hinge, re-square the gate, and the opener stops straining and tripping its limit switch.
LiftMaster systems tend to tear welds at the operator arm when a gate drifts out of alignment. We cut out the old weld, grind the area clean, weld the bracket back square, and run the full open-close cycle to confirm the motor is not fighting itself. The same applies to FAAC, BFT, and any other make in the driveway. The metal side of the gate does not care what brand the motor is, and neither do we.
Signs You Need Gate Parts & Welding Right Now
- The gate scrapes or drags on the ground. This means a hinge, post, or roller has failed and the gate is now plowing instead of swinging. Every cycle is adding wear to the opener motor, and a dragging gate is the number one reason motors burn out before their time.
- You can see a crack in the metal, especially where a bracket meets the frame. Gate frames crack at stress points, and small cracks grow with every open and close. A crack that is welded today is a quick fix. A crack that snaps is a gate on the ground.
- The gate sags and will not latch without lifting it. When you have to lift the gate to close it, the frame has racked out of square. That strain lands on the opener, the latch, and the remaining hinges. Straightening and re-welding now prevents replacing all three later.
- The gate rattles, chatters, or bangs when it moves. Sliding gates chatter on worn rollers. Swing gates bang on loose hinges or broken pickets. Noise is the first warning before the visible failure, and catching it early usually means a smaller repair bill.
- The post is leaning, even slightly. A leaning post means the footing underneath has moved or the post has failed at grade. The gate will only get lower and heavier on its hardware. Post replacement is measured in hundreds, not thousands, when it is caught before the gate pulls the post completely over.
Any one of these on its own is worth a phone call. All of them together mean the gate is working against you every time you leave the house. Call (254) 345-4831 and we’ll make it right before it gets worse.
Our Gate Parts & Welding Process - Step by Step
We do this work the same way every time, so you know what to expect from the first phone call to the final walk-around. No surprises, no scope creep, no invoice that does not match the quote.
- 1
Call and describe what the gate is doing. You call, a live person answers, and we ask the right questions: what noise it makes, where it drags, what it looks like at the hinge. That conversation tells us which parts and tools to bring on the first visit.
- 2
We inspect and diagnose on site. Our technician checks the gate square, the hinge wear, the post footing, the welds, and the opener’s strain. We check the entire gate, not just the loudest part, because a failing hinge often takes out a roller or a latch on the way down.
- 3
You get a written price before any work starts. We quote the repair in writing, explain what is urgent and what can wait, and you approve it before we turn a single bolt. The price you approve is the price on the invoice. Every time.
- 4
We do the work - most jobs in one visit. Most hinge, roller, latch, and weld repairs are finished the same day. We bring the common parts for your gate type on the truck, and we weld on site, so there is no week-long wait for a shop to get around to it.
- 5
We test, verify, and walk you through it. After the repair, we cycle the gate several times by hand and by motor, check the latch engagement, and make sure the gate is square. Then we walk you through what was wrong, what we fixed, and what to watch for so it never becomes an emergency. The job is covered by our written 90-Day Done Right Promise.
How Much Does Gate Parts & Welding Cost in Flower Mound?
Gate parts and welding in Flower Mound runs a wide range because the work ranges from a $40 roller swap to a full post replacement with welding and concrete. A typical hinge replacement on a standard swing gate runs $180 to $340. Replacing one gate post, including removing the old post, setting the new one, and re-hanging the gate, typically runs $450 to $900. Custom welding repairs are usually quoted by the job, and most small to medium welds fall between $150 and $500 depending on access and how much has to come apart to reach the crack.
What moves the price is the gate’s weight and size, whether the post footing needs re-poured, how much rust or previous damage has to be cut out, and whether the gate has to come off its hinges to do the fix safely. You avoid overpaying by getting a second opinion, which we make easy: we offer a free second opinion on any written estimate, no strings attached. Every quote is free, in writing, and settled before any work starts. Call (254) 345-4831 and we’ll give you a straight number.
Gate Parts & Welding Near Flower Mound - Our Service Area
We serve Flower Mound and the surrounding communities, including Bartonville, Copper Canyon, Double Oak, Highland Village, and Hickory Creek. Most parts and welding jobs in Flower Mound get same-day or next-day visits, and we always arrive when we say we will. For more on what we do, see our Gate Parts & Welding in Flower Mound page or explore our home page for the full scope of gate services. We also serve Gate Parts & Welding in Argyle and Gate Parts & Welding in Denton for clients in the broader area.
Serving Flower Mound, TX - Our Local Coverage Area
We’re based in the Flower Mound area and know this community well, and we also offer our Gate Parts & Welding in Argyle. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Flower Mound
Gate parts and welding covers the physical hardware and steel work on a driveway gate: hinges, posts, rails, rollers, latches, and the welds that hold them together. It is the mechanical side of the gate, separate from the motor and opener. If the gate sags, drags, cracks, or will not latch, this is the service that fixes it.
Most hinge, roller, latch, and small weld repairs are finished in a single visit, usually within one to two hours on site. Larger jobs like post replacement may take half a day because of the concrete work involved. We stock common hardware on the truck so we do not have to leave and come back for parts.
Small repairs like roller swaps run $40 to $120, hinge replacement runs $180 to $340, and post replacement runs $450 to $900. Custom welding is quoted by the job, with most repairs between $150 and $500. We give a written price before any work begins, and you can call (254) 345-4831 for a free estimate on your specific gate.
Yes. We service and repair gates paired with LiftMaster, Mighty Mule, FAAC, BFT, and all other major opener brands. The metal side of the gate, the hinges, welds, and hardware, is our specialty, and we make sure the repair works with whatever motor is on the driveway, not against it.
In most cases in Flower Mound, yes. We keep same-day availability for gate emergencies because a gate that will not close leaves your property open overnight. Call (254) 345-4831 and a live person will tell you exactly when we can be there, 24 hours a day.
Every repair is covered by our written 90-Day Done Right Promise. If it is not right, we come back and make it right. No paperwork, no arguing, no exceptions. That applies to every hinge, weld, post, roller, and latch we install or repair.
Make sure the area around the gate is clear of vehicles and debris so we have room to work, and have your gate remote or opener code ready if you have an automated gate. If you can describe the problem when you call, we will arrive with the right parts on the truck. We handle everything else from there.
Schedule Your Gate Parts & Welding Service in Flower Mound Today
Your gate worked fine for decades. It can work fine for decades more, but only if the parts and metal are set right. Ironworks Gate Co. is one call away, 24 hours a day, 7 days a week. Call (254) 345-4831 for a free, no-obligation estimate. Victor Salinas and our team will be there when we say, quote a straight price, and back the work in writing. A square deal. No surprises on the bill.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Flower Mound since 1984.