Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Double Oak
Gate parts and welding in Double Oak usually comes down to one of three jobs: a hinge that finally let go, a post that has heaved out of plumb, or a steel panel that needs cutting and welding back square. Most Double Oak calls we run are completed same-day, and the price is settled before any work starts, so there’s no surprise on the bill. If your gate is dragging, sagging, or not latching, call (254) 345-4831 and a live person will answer. We know the driveways off Chinn Chapel, Simmons, and Waketon, and we keep the repair van stocked with the parts those older Double Oak gates actually need.
Key Takeaways:
- Hinge replacement in Double Oak typically runs $185-$420 depending on gate weight and whether the post needs re-setting.
- Post replacement with proper clay-soil footing runs $375-$850 per post.
- We service older LiftMaster, DoorKing, Elite, and Mighty Mule operators without pushing a full replacement when a retrofit makes sense.
- Every job is covered by a written 90-Day Done Right Promise.
Why Ironworks Gate Co. Is Double Oak’s Preferred Gate Parts & Welding Company
We’re a gate-only shop. We do not cut lawns, we do not paint houses, we do not moonlight as general contractors. For over 42 years, our work has been hinges, posts, gate frames, rollers, latches, and the welding that holds it all together. Double Oak is different from our other North Texas routes because of the horse properties. A single service call might start at a street-side ornamental iron driveway gate and end at a pipe pasture gate behind the barn. Few repair companies are set up for both ends of that spectrum. We are.
Our crews are background-checked and uniformed. They arrive when we say they will, and they work under the K.E.Y.S. code we’ve kept since the beginning: Krafted right, Every time, Your home first, Standing behind it. Victor Salinas runs the shop, and he still personally reviews the harder fabrication and post-reset jobs before we schedule them. That kind of oversight is uncommon, and it matters on a 400-pound iron gate hung in 1987 off Simmons Road.
We’re also trained and equipped on nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your operator is original to the property and the control board finally gave out, we can usually tell you straight whether it’s worth a retrofit or time to swap the unit. That’s a conversation we have weekly with Double Oak homeowners.
Our Gate Parts & Welding Services in Double Oak
Hinge Replacement
Most Double Oak gates built in the 1980s and 1990s hang on barrel hinges or heavy strap hinges that have been carrying weight for 30 years or more. When the gate starts to sag, the hinge is usually the first failure point, often with a cracked weld at the post plate. We cut the old hinges off, weld new ones on with proper gusseting, and realign the gate so the latch catches clean. On ornamental iron gates, we grind the welds smooth and match the finish so the repair does not read as a patch job from the street.
Post Replacement
Double Oak’s expansive clay is the single biggest reason posts fail here. The soil under a gate post swells in wet springs and shrinks through dry summers, and over a decade that movement slowly levers the post out of true. A post that’s leaned only three degrees is enough to make a swing gate drag and refuse to latch. We dig the old footing, set the new post deeper with a proper concrete collar, and brace it plumb before welding the gate back on. In Double Oak clay, we go deeper than standard practice because we know what the soil will do in the next drought cycle.
Rail Repair
Slide gates on Double Oak acreage commonly use rack-and-pinion drives, and after 20 to 30 years the rack teeth wear, the rail sections bend, and the gate starts to shudder instead of glide. We straighten bent top and bottom rails, weld cracked joints, and install new rack sections cut to length. If the rail is too far gone, we’ll tell you honestly and quote a replacement. We’ve learned over the years that patching a badly worn rail just moves the failure further down the line, and Double Oak homeowners don’t call us for temporary fixes.
Custom Welding
This is the work that separates a gate specialist from a handyman with a flux-core welder in the truck. We do structural repairs: cracked hinge plates, broken pickets, snapped top rails, torn latch mounts. But we also fabricate. Need a custom height extension added to a pasture gate because a new horse clears it? Need to widen a driveway gate opening and build a new leaf to match the existing ornamental design? In Double Oak, we regularly weld pipe pasture gates from scratch, match picket spacing to the original street gate, and build bracing that looks intentional rather than bolted-on. Victor has a fabricator’s eye; if it’s metal and it’s on your gate, we can repair or rebuild it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Double Oak
We keep a rolling inventory for the operators most common on older Double Oak properties: LiftMaster control boards, DoorKing and Elite limit switches, Mighty Mule arms and remotes, plus generic weld-on hinges and steel stock that fit the custom gates of this area. That inventory means we often complete a parts-and-welding repair in a single visit rather than waiting on a regional distributor. And when a part is obsolete, we say so plainly and lay out the retrofit options instead of slapping on a universal component that will fail again in eight months.
Common Gate Parts & Welding Problems We See in Double Oak Homes
- Gate posts heaved out of plumb by expansive clay. Denton County’s clay soils swell with spring rain and shrink hard through August. Posts set 20-30 years ago with shallow footings are now leaning, and the gate binds or misses the latch. We reset the post with a deeper footing and often weld a reinforcement plate to correct the alignment.
- Caliche dust inside operator housings. A meaningful share of Double Oak driveways are unpaved caliche or decomposed granite, and the fine dust that kicks up every time a vehicle passes works its way into gearboxes and control boards. We open the operator, clean the contacts, replace what’s shorted, and advise on sealing the housing. This failure mode is far more common here than in paved subdivisions four miles south.
- Worn rack and pinion drives on older slide gates. Slide gates installed in the 1990s and early 2000s are hitting the end of their rack wear cycle. Teeth are stripped, rail sections are bent, and the gate now grinds instead of rolling. We replace the rack and rollers, and when the rail itself is fatigued we quote a rail replacement with the welding included.
- Cracked hinge welds on heavy ornamental gates. Long iron driveway gates hung on undermount hinges eventually crack the weld at the post plate. The gate sags, the photo-eyes lose alignment, and the opener strains until it trips. We grind out the old weld, reinforce the joint, and hang the gate back square.
Pricing for Gate Parts & Welding in Double Oak, TX
Here’s what we quote in the Double Oak market, and these numbers hold unless we find something structural on-site: hinge replacement runs $185-$420 per hinge depending on gate weight and whether the post plate needs rebuilding. Post replacement runs $375-$850 per post with the deeper clay-soil footing included. Rail repair or rack replacement runs $250-$600 per section. Custom welding jobs start at $150 for small crack repairs and scale from there; a full pasture gate fabrication typically falls between $600 and $1,400 depending on size and steel. We quote the job before we touch a bolt, and you get the written 90-Day Done Right Promise on every repair. Standing offers apply to Double Oak customers too: $50 off any repair over $250, a free second opinion on any written estimate, and a 5% senior and veteran discount, always. Call (254) 345-4831 for a free estimate.
We Also Serve Cities Near Double Oak
Our Gate Parts & Welding crews run routes through Double Oak weekly, and we extend the same service to Flower Mound, Argyle, Denton, and Bartonville. If you’re just outside Double Oak but still in the Denton County clay belt, call us and we’ll let you know which day we’re in your area.
Serving Double Oak, TX - Our Local Coverage Area
We’re based in the Double Oak area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Double Oak
Expansive clay shrinks and swells with seasonal moisture, which slowly levers gate posts out of plumb and cracks the hinge welds at the plate. In Double Oak we regularly see posts that have moved 2-3 inches out of true over a decade. The fix is re-setting the post with a deeper concrete footing sized for clay movement, then cutting and re-welding the hinge plates so the gate hangs square again. Call (254) 345-4831 and we’ll inspect yours and quote the exact repair.
Yes, often we can. Original LiftMaster operators from the 1990s share many parts across model years, and we carry common control boards, limit switches, and capacitors. We’ll test the unit and tell you honestly if a retrofit makes sense or if the cumulative wear means replacement is cheaper than another repair in a year. The assessment is free, and the decision is yours.
In Double Oak, the June drag is almost always a post problem. The clay has dried and shrunk after the spring rains, and the post has settled or leaned enough to drop the gate’s leading edge. We check the post with a level, determine how far it has moved, and quote a re-set rather than just adjusting the hinges, which would be a temporary fix. Call us at (254) 345-4831 and we’ll come put a level on it.
We do. We keep common Viking and DoorKing roller assemblies, rack sections, and rail stock in our service van, which means most Double Oak slide gate repairs finish in a single trip. If a part is model-specific and we don’t have it on the truck, we can usually source it locally within one business day.
Yes. Regardless of when your gate was installed, if it is automated it must meet current UL 325 entrapment protection standards, which means working photo-eyes and a functional reverse mechanism. We test this on every automatic gate service call in Double Oak, and if yours are misaligned or dead, we fix them before we leave, because a gate that cannot detect a person or a horse is a genuine hazard. For a safety check or any parts repair, call (254) 345-4831.
Contact Ironworks Gate Co. for Gate Parts & Welding in Double Oak
We run Double Oak routes every week, and our dispatch is set up so a real person answers when you call, 24 hours a day. No phone tree, no answering service. Tell us what the gate is doing, and we’ll get a crew out to your place on the next available route, give you a written price before any work starts, and stand behind the repair with the 90-Day Done Right Promise. If you have a sagging post, a cracked weld, a dead opener, or a pasture gate that hasn’t closed right since the spring rains, call (254) 345-4831. We’ll be there when we say.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Double Oak and the surrounding Denton County area.